Leg extension machine with an orange selector pin. 8/8/8 Leg Extension Drop Set Protocol for Hypertrophy.

ARTICLE

8/8/8 Leg Extension Drop Set: A Hypertrophy Protocol

If I want more work from the quads at the end of a lower-body session, the 8/8/8 leg extension drop set is one way I’ll programme it. You start with a hard set of eight, reduce the load and do another eight, then reduce it again for the final eight. Take only as long as you need to move the pin. That gives you 24 repetitions in one extended set.

The main thing to get right is the load on each stage. Each reduction needs to account for the fatigue from the preceding eight reps. A lifter who can do eight comfortably at 50 kg when fresh may only get six at that weight immediately after a hard eight at 60 kg. Write down the loads you actually use for the three stages. That’s how you turn a drop set into something you can progress.

Where I use it in a hypertrophy meso

I’d use it in the B or C series when the quads are a priority. If the A series is a squat and the B series is a split squat, the drop set can go on the last set of leg extensions in the C series. The squat and split squat give the lifter the earlier work. The leg extension gives them a way to add direct knee-extension work without having to maintain the balance and position of another compound lift.

Start by replacing one straight set of leg extensions. For example, if the programme calls for three sets, keep the first two and run 8/8/8 on the third. Keep the rest between the preceding straight sets as prescribed. The short transitions apply within the drop set itself. Once you’ve seen what it does to the next lower-body session, you can decide whether there’s a case for using it more often.

I’d use straight sets for trainees who are still getting their seat position and range consistent. The drop set is easier to judge with a lifter who can already make the last hard rep of a normal set look like the first, apart from the speed it takes to get through it.

How to load the three stages

First eight. Pick a weight that makes the eighth rep hard at the range and tempo you prescribed. Leave a rep or two in reserve the first time you try it. If the eighth rep of the opening stage already requires the lifter to lift the hips or shorten the range, bring the opening load down.

Second eight. Take enough weight off to get eight reps after the first stage. A 10 kg reduction from 60 kg is 16.7%. That’s a starting point in the example below. The lifter’s actual performance and the spacing on the stack determine where the pin goes.

Final eight. Make the second reduction based on what the lifter has left after 16 reps. Look at the effort on reps seven and eight and whether they still extend through the range you set. If they can clearly do several more reps and the earlier stages were correctly loaded, use a smaller final drop the next time around.

What I’d change after an 8/6/8

Say the lifter starts with 60 kg, then drops to 50 kg and 40 kg. They get eight clean reps at 60 kg, six at 50 kg and eight at 40 kg. If the next available setting is 45 kg, my next prescription would be 60/45/40 kg. I’d keep the opening load because the first eight were at the right effort. I’d keep the final load for the first retest because doing two extra reps at the middle weight can make the last eight harder.

Once the lifter gets 8/8/8 at 60/45/40 kg, look at the last few reps of each stage before progressing it. If the final stage is the only one with room and the stack has an increment between 40 and 45 kg, increase that load first. If there’s no usable increment, keep 40 kg and repeat the sequence until there’s a reason to change an earlier stage. A larger middle weight is only worth trying when the lifter has some room on those eight reps as well.

Keep the position and range consistent

Use the same machine and record the seat and roller settings. Set the start and finish positions before you add weight. Keep the hips on the seat and control the roller on the way down. If the lifter can only reach the prescribed finish on six reps, record six. Moving the roller partway twice after that tells you where the stage broke down.

Also note how long it took to change the pin. If the first exposure had two quick changes and the next had a 30-second break before the last eight, you’ve changed the prescription. It’s worth knowing that before you put more weight on next session.

Programme the drop set for what it does in the meso. If the lifter can progress the leg extension and still get through the next squat or split-squat session as intended, keep it in. If performance on the priority work repeatedly drops, take the drop set out before cutting the work you put first for a reason.

Dale Hansford

WRITTEN BY

Dale Hansford

Strength & Conditioning Coach with 15+ years of applied experience. Specialising in program design, periodisation, and coaching education for serious coaches and athletes.

Learn more about Dale →

TAKE THE NEXT STEP

Want to Master Program Design?

Learn how to write systematic, evidence-based training programs that produce real results. Explore the mentorship, self-paced courses, or free resources.

KEEP READING

Related Articles